Doors just opened. It's still the warm-up in here. Grab your spot and check back as the floor fills up.

B2B Beta

Set up your audio

Denon DJ SC6000 / SC6000M, with an X1850 PRIME

Choose your setup… (Practice, Home or Pro). Choice of setup does not change recording or streaming quality.

Practice: your laptop's own speakers

Wiring: computer, Denon DJ X1850 PRIME, headphonesComputerUSBDenon DJ X1850PRIMEUSBMASTER(XLR)HeadphoneOutputs(6.35 mm / 3.5 mm)HeadphonesUSB cableleave empty.

Fine for practice. For louder sound, use Pro or Home.

Always beatmatch in headphones, your computer audio will be slightly out of phase.

Plug your headphones into your mixer, not your computer.

Strongly recommended: connect your computer to the internet with an Ethernet cable. Wi-Fi works, but a cable keeps the set steadier.

FromToCable
Denon DJ X1850 PRIMEUSBComputerUSBUSB cable
Denon DJ X1850 PRIMEHeadphone OutputsHeadphones

Home: your computer feeds your speakers

Wiring: computer, Denon DJ X1850 PRIME, powered speakers or amp, headphonesComputerUSBsound outDenon DJ X1850PRIMEUSBMASTER(XLR)HeadphoneOutputs(6.35 mm / 3.5 mm)Powered speakersor ampHeadphonesUSB cableleave empty.3.5 mm jack to two XLR, or3.5 mm jack to two jack (¼"), or3.5 mm jack to two RCA

From your computer's 3.5 mm headphone socket. Advice only: computer volume between half and three quarters. For better sound, we recommend an audio interface.

Always beatmatch in headphones, your computer audio will be slightly out of phase.

Plug your headphones into your mixer, not your computer.

Strongly recommended: connect your computer to the internet with an Ethernet cable. Wi-Fi works, but a cable keeps the set steadier.

FromToCable
Denon DJ X1850 PRIMEUSBComputerUSBUSB cable
ComputerSound outPowered speakers or amp3.5 mm jack to two XLR, or 3.5 mm jack to two jack (¼"), or 3.5 mm jack to two RCA
Denon DJ X1850 PRIMEHeadphone OutputsHeadphones

Pro: an audio interface feeds your speakers

Wiring: computer, audio interface, Denon DJ X1850 PRIME, powered speakers or amp, headphonesComputerUSBUSBAudiointerfaceUSBoutputsDenon DJ X1850PRIMEUSBMASTER(XLR)HeadphoneOutputs(6.35 mm / 3.5 mm)Powered speakersor ampHeadphonesUSB cableleave empty.USB cable

See our suggested audio interfaces.

Always beatmatch in headphones, your computer audio will be slightly out of phase.

Plug your headphones into your mixer, not your computer.

Strongly recommended: connect your computer to the internet with an Ethernet cable. Wi-Fi works, but a cable keeps the set steadier.

FromToCable
Denon DJ X1850 PRIMEUSBComputerUSBUSB cable
Audio interfaceUSBComputerUSBUSB cable
Audio interfaceOutputsPowered speakers or amp
Denon DJ X1850 PRIMEHeadphone OutputsHeadphones

Your computer

Your gear

Club mixer (with CDJs, turntables or a controller)

Playing vinyl? Plug your turntables into the mixer as usual: your B2B partner hears your records through it. BPM, key and the shared waveform need digital players.

Your mixer

Denon DJ SC6000 / SC6000M, with an X1850 PRIME

  1. Download page: https://www.denondj.com/downloads (X1850 PRIME under DJ Mixers)
  2. On a Mac: Nothing to install. Check it's listed in Audio MIDI Setup; if it isn't, run "Firmware Updater (Mac)" from that page. The update restores all hardware settings to their factory defaults.
  3. On Windows: Download "Windows Driver" v1.0.4 and install it.
  4. On the mixer, press and hold Quantize/Utility. Turn FX Select/Enter to Advanced Audio and press it, then do the same for USB Audio and Master, and pick a USB pair. Press and hold again to leave.
  5. On a Mac: macOS 26 Tahoe and 15 Sequoia: supported.
  6. Connect this computer to the mixer's USB 1 (or 2) port. Sound from other DJs is allocated a channel on your mixer. This is your B2B channel. Choose a B2B channel on your mixer by turning the channel's Input Select to USB, and its USB 1/2 switch to match your computer's input - either USB 1 or 2.
  7. Keep your master level up: your B2B partner hears your mix through it.
  8. On Windows: On the Sound panel's Playback tab, open your mixer's Properties, go to Advanced, and untick "Allow applications to take exclusive control of this device". Do the same on the Recording tab. Otherwise another app can take over your mixer, and DJ back 2 back goes silent.
  9. In DJ back 2 back's Settings → Audio, find Source and pick the X1850 PRIME with Source channels set to the pair you set for Master. Under Line out, pick the X1850 PRIME with Line out channels set to the pair that plays on your B2B channel. Under Speakers out, pick where your speakers are plugged in.

PA or Mains

  • Powered speakers: run a cable from your audio interface's speaker outputs straight into the speakers.
  • On a Mac: Powered speakers: run a cable from your Mac's output straight into the speakers.
  • On Windows: Powered speakers: run a cable from your PC's output straight into the speakers.
  • Your laptop's own speakers play your set and your B2B partner's. Fine for practice; for louder sound, use Pro or Home.
  • An amp and speakers: run the same cable into the amp's input. The amp drives your speakers as usual.
  • In your first session: while you play, your track should sound once and clean. Once your B2B partner has taken over, your speakers play their set, it's not in your headphones. After handover it's back on your mixer ready to beatmatch.

Your B2B channel's fader (optional)

  • In Settings → MIDI Learn, learn your B2B channel's fader, with your mixer's MIDI on.

In a set

In a set, the app shows these buttons and messages: READY · Set starts in · Handover · Accept handover · Confirm partner is mixed out · Fader up.

  • When offered a handover, make sure your B2B channel's fader is up, then click Accept and mix in your track.
  • You have control. Once you're in, confirm your partner is mixed out.
  • When you're ready, you hand over, your partner accepts and tells you when you're mixed out, and you can stop your track.

Your internet

Use a wired connection wherever possible.

Upload speed: 5 Mbps or more, or quality may drop.

How a set sounds depends on both DJs' internet connections, which we don't control. We can't promise a connection will be good enough.

Any issues? Email support@djback2back.com