Doors just opened. It's still the warm-up in here. Grab your spot and check back as the floor fills up.

B2B Beta

Set up your audio

Pioneer DDJ-REV7, by USB

Choose your setup… (Practice, Home or Pro). Choice of setup does not change recording or streaming quality.

Practice: your laptop's own speakers

Wiring: computer, Pioneer DDJ-REV7, by USB, headphonesComputerUSBPioneer DDJ-REV7,by USBUSB ports (USB-B)MASTER 1terminals(XLR)PHONESterminals(6.35 mm / 3.5 mm)HeadphonesUSB-B to USB-C, or USB-B to USB-Aleave empty, or turnits level fullydown.

Fine for practice. For louder sound, use Pro or Home.

Always beatmatch in headphones, your computer audio will be slightly out of phase.

Plug your headphones into your mixer or controller, not your computer.

FromToCable
Pioneer DDJ-REV7, by USBUSB portsComputerUSBUSB-B to USB-C, or USB-B to USB-A
Pioneer DDJ-REV7, by USBPHONES terminalsHeadphones

Home: your computer feeds your speakers

Wiring: computer, Pioneer DDJ-REV7, by USB, powered speakers or amp, headphonesComputerUSBsound outPioneer DDJ-REV7,by USBUSB ports (USB-B)MASTER 1terminals(XLR)PHONESterminals(6.35 mm / 3.5 mm)Powered speakersor ampHeadphonesUSB-B to USB-C, or USB-B to USB-Aleave empty, or turnits level fullydown.3.5 mm jack to two XLR, or3.5 mm jack to two jack (¼"), or3.5 mm jack to two RCA

From your computer's 3.5 mm headphone socket. Advice only: computer volume between half and three quarters. For better sound, we recommend an audio interface.

Always beatmatch in headphones, your computer audio will be slightly out of phase.

Plug your headphones into your mixer or controller, not your computer.

FromToCable
Pioneer DDJ-REV7, by USBUSB portsComputerUSBUSB-B to USB-C, or USB-B to USB-A
ComputerSound outPowered speakers or amp3.5 mm jack to two XLR, or 3.5 mm jack to two jack (¼"), or 3.5 mm jack to two RCA
Pioneer DDJ-REV7, by USBPHONES terminalsHeadphones

Pro: an audio interface feeds your speakers

Wiring: computer, audio interface, Pioneer DDJ-REV7, by USB, powered speakers or amp, headphonesComputerUSBUSBAudiointerfaceUSBoutputsPioneer DDJ-REV7,by USBUSB ports (USB-B)MASTER 1terminals(XLR)PHONESterminals(6.35 mm / 3.5 mm)Powered speakersor ampHeadphonesUSB-B to USB-C, or USB-B to USB-Aleave empty, or turnits level fullydown.USB cable

See our suggested audio interfaces.

Always beatmatch in headphones, your computer audio will be slightly out of phase.

Plug your headphones into your mixer or controller, not your computer.

FromToCable
Pioneer DDJ-REV7, by USBUSB portsComputerUSBUSB-B to USB-C, or USB-B to USB-A
Audio interfaceUSBComputerUSBUSB cable
Audio interfaceOutputsPowered speakers or amp
Pioneer DDJ-REV7, by USBPHONES terminalsHeadphones

Your computer

Your gear

Standalone controller

Your model

Pioneer DDJ-REV7, by USB

  1. On a Mac: Install only the DDJ-REV7's Setting Utility, from AlphaTheta's support page.
  2. On Windows: Install Pioneer's audio driver for the DDJ-REV7, from AlphaTheta's support page; the Setting Utility comes with it.
  3. In the DDJ-REV7 Setting Utility's Audio Output, set CH 1 (USB 1/2) to MIX(REC OUT with MIC). That's your mix.
  4. On a Mac: Sound from other DJs is allocated a channel on your unit. This is your B2B channel. Choose a B2B channel on your unit by sliding the channel's input selector to match your computer's input - the computer mark (a laptop icon), A or B.
  5. On Windows: Your B2B channel is CH1: slide CH1's input selector to the computer mark (a laptop icon), A or B, whichever your computer is connected to.
  6. Master and booth levels off to infinity to avoid phasing.
  7. On a Mac: In DJ back 2 back's Settings → Audio, find Source and pick the DDJ-REV7 with Source channels USB 1/2. Under Line out, pick the DDJ-REV7 with Line out channels for your B2B channel: USB1/2 for CH1, 3/4 for CH2.
  8. On Windows: On the Sound panel's Playback tab, open your unit's Properties, go to Advanced, and untick "Allow applications to take exclusive control of this device". Do the same on the Recording tab. Otherwise another app can take over your unit, and DJ back 2 back goes silent.
  9. On Windows: In DJ back 2 back's Settings → Audio, find Source and pick the DDJ-REV7 with Source channels USB 1/2. Under Line out, pick the DDJ-REV7 with Line out channels for your B2B channel: USB1/2 for CH1.

PA or Mains

  • Powered speakers: run a cable from your audio interface's speaker outputs straight into the speakers.
  • On a Mac: Powered speakers: run a cable from your Mac's output straight into the speakers.
  • On Windows: Powered speakers: run a cable from your PC's output straight into the speakers.
  • Your laptop's own speakers play your set and your B2B partner's. Fine for practice; for louder sound, use Pro or Home.
  • An amp and speakers: run the same cable into the amp's input. The amp drives your speakers as usual.
  • In your first session: while you play, your track should sound once and clean. Once your B2B partner has taken over, your speakers play their set, it's not in your headphones. After handover it's back on your mixer ready to beatmatch.

Your B2B channel's fader (optional)

  • In Settings → MIDI Learn, learn your B2B channel's fader, with your mixer's MIDI on.

In a set

In a set, the app shows these buttons and messages: READY · Set starts in · Handover · Accept handover · Confirm partner is mixed out · Fader up.

  • When offered a handover, make sure your B2B channel's fader is up, then click Accept and mix in your track.
  • You have control. Once you're in, confirm your partner is mixed out.
  • When you're ready, you hand over, your partner accepts and tells you when you're mixed out, and you can stop your track.

Your internet

Use a wired connection wherever possible.

Upload speed: 5 Mbps or more, or quality may drop.

How a set sounds depends on both DJs' internet connections, which we don't control. We can't promise a connection will be good enough.

Any issues? Email support@djb2b.com