Doors just opened. It's still the warm-up in here. Grab your spot and check back as the floor fills up.

B2B Beta

Set up your audio

Pioneer DDJ-SX3, by USB

Choose your setup… (Practice, Home or Pro). Choice of setup does not change recording or streaming quality.

Practice: your laptop's own speakers

Wiring: computer, Pioneer DDJ-SX3, by USB, headphonesComputerUSBPioneer DDJ-SX3,by USBUSBMASTEROUT 1terminals(XLR)HEADPHONESjacks(6.35 mm / 3.5 mm)HeadphonesUSB cableleave empty, or turnits level fullydown.

Fine for practice. For louder sound, use Pro or Home.

Always beatmatch in headphones, your computer audio will be slightly out of phase.

Plug your headphones into your mixer or controller, not your computer.

FromToCable
Pioneer DDJ-SX3, by USBUSBComputerUSBUSB cable
Pioneer DDJ-SX3, by USBHEADPHONES jacksHeadphones

Home: your computer feeds your speakers

Wiring: computer, Pioneer DDJ-SX3, by USB, powered speakers or amp, headphonesComputerUSBsound outPioneer DDJ-SX3,by USBUSBMASTEROUT 1terminals(XLR)HEADPHONESjacks(6.35 mm / 3.5 mm)Powered speakersor ampHeadphonesUSB cableleave empty, or turnits level fullydown.3.5 mm jack to two XLR, or3.5 mm jack to two jack (¼"), or3.5 mm jack to two RCA

From your computer's 3.5 mm headphone socket. Advice only: computer volume between half and three quarters. For better sound, we recommend an audio interface.

Always beatmatch in headphones, your computer audio will be slightly out of phase.

Plug your headphones into your mixer or controller, not your computer.

FromToCable
Pioneer DDJ-SX3, by USBUSBComputerUSBUSB cable
ComputerSound outPowered speakers or amp3.5 mm jack to two XLR, or 3.5 mm jack to two jack (¼"), or 3.5 mm jack to two RCA
Pioneer DDJ-SX3, by USBHEADPHONES jacksHeadphones

Pro: an audio interface feeds your speakers

Wiring: computer, audio interface, Pioneer DDJ-SX3, by USB, powered speakers or amp, headphonesComputerUSBUSBAudiointerfaceUSBoutputsPioneer DDJ-SX3,by USBUSBMASTEROUT 1terminals(XLR)HEADPHONESjacks(6.35 mm / 3.5 mm)Powered speakersor ampHeadphonesUSB cableleave empty, or turnits level fullydown.USB cable

See our suggested audio interfaces.

Always beatmatch in headphones, your computer audio will be slightly out of phase.

Plug your headphones into your mixer or controller, not your computer.

FromToCable
Pioneer DDJ-SX3, by USBUSBComputerUSBUSB cable
Audio interfaceUSBComputerUSBUSB cable
Audio interfaceOutputsPowered speakers or amp
Pioneer DDJ-SX3, by USBHEADPHONES jacksHeadphones

Your computer

Your gear

Standalone controller

Your model

Pioneer DDJ-SX3, by USB

  1. Install Pioneer's audio driver for the DDJ-SX3, on a Mac or Windows, from AlphaTheta's support page.
  2. Play a track at step 3 of DJ back 2 back's setup: it finds the pair your mix is on.
  3. Sound from other DJs is allocated a channel on your unit. This is your B2B channel. Choose a B2B channel on your unit by sliding the channel's input select switch to match your computer's input - either USB A or B.
  4. Master and booth levels off to infinity to avoid phasing.
  5. On Windows: On the Sound panel's Playback tab, open your unit's Properties, go to Advanced, and untick "Allow applications to take exclusive control of this device". Do the same on the Recording tab. Otherwise another app can take over your unit, and DJ back 2 back goes silent.
  6. In DJ back 2 back's Settings → Audio, find Source and pick the DDJ-SX3 with Source channels set to the pair DJ back 2 back's setup found. Under Line out, pick the DDJ-SX3 with Line out channels set to the pair that plays on your B2B channel. Under Speakers out, pick where your speakers are plugged in.

PA or Mains

  • Powered speakers: run a cable from your audio interface's speaker outputs straight into the speakers.
  • On a Mac: Powered speakers: run a cable from your Mac's output straight into the speakers.
  • On Windows: Powered speakers: run a cable from your PC's output straight into the speakers.
  • Your laptop's own speakers play your set and your B2B partner's. Fine for practice; for louder sound, use Pro or Home.
  • An amp and speakers: run the same cable into the amp's input. The amp drives your speakers as usual.
  • In your first session: while you play, your track should sound once and clean. Once your B2B partner has taken over, your speakers play their set, it's not in your headphones. After handover it's back on your mixer ready to beatmatch.

Your B2B channel's fader (optional)

  • In Settings → MIDI Learn, learn your B2B channel's fader, with your mixer's MIDI on.

In a set

In a set, the app shows these buttons and messages: READY · Set starts in · Handover · Accept handover · Confirm partner is mixed out · Fader up.

  • When offered a handover, make sure your B2B channel's fader is up, then click Accept and mix in your track.
  • You have control. Once you're in, confirm your partner is mixed out.
  • When you're ready, you hand over, your partner accepts and tells you when you're mixed out, and you can stop your track.

Your internet

Use a wired connection wherever possible.

Upload speed: 5 Mbps or more, or quality may drop.

How a set sounds depends on both DJs' internet connections, which we don't control. We can't promise a connection will be good enough.

Any issues? Email support@djb2b.com